Greenhouse Pipe

Yuantai Derun is a professional greenhouse pipe manufacturer with 25 years of manufacturing experience, mainly producing greenhouse galvanized pipe fittings, including greenhouse galvanized tubing, zinc aluminum magnesium coated greenhouse pipes. At present, the following main materials are commonly used in regular greenhouse greenhouses:

1.Square tube: Generally used on the pillars of intelligent greenhouses, this type of square tube is generally 70 * 50, 50 * 100, 100 * 100, 120 * 120, 150 * 150 or other larger specifications. Smaller square tubes such as 50 * 50 are used on the horizontal rod of the greenhouse.

2.Circular tube: A frame (column, inclined beam, longitudinal tie rod) used to build a greenhouse, or a secondary load-bearing structure that transmits force to the main load-bearing structure after being subjected to force. It is the skeleton of a greenhouse, and common models are generally φ 25 φ 32 φ 48 φ 60.

3.Elliptical tube: Elliptical tube is a new product launched in recent years. Compared to circular tubes, it has particularly good pressure resistance. However, due to the fact that existing elliptical tubes are made of galvanized tape, their anti-corrosion performance is inferior to that of circular tubes, and they are only selected in a few regions. Elliptical tubes are generally made by flattening and bending hot-dip galvanized square tubes.

4.Cross shaped steel: It is commonly used on the top of intelligent greenhouses to form a cross shaped steel skeleton. The advantage is low cost, but compared to square tubes, it has poorer stability. Mainly used in areas with low stress and anti-corrosion requirements.

5.Steel pipe wall thickness: ordinary planting shed, round pipe φ 25 φ 32 is the main structure, with a thickness mostly ranging from 1.5 to 2.75mm

Ordinary breeding shed, elliptical tube 25 × 50mm, 30 × 60mm, 30 × 70mm, 30 × 80mm, 40 × 80mm

1) Hanging plating: also known as hanging plating, it has the best quality, the highest amount of zinc applied, and the strongest anti-corrosion ability. The process roughly involves pickling the steel pipe, removing impurities from it, and immersing the entire steel pipe in a zinc pool. After several lifting cycles of more than ten seconds, it is taken out and cooled down. The zinc content on the steel pipe of the hanging zinc process reaches 400-600 grams, and the service life of the hanging galvanized steel pipe is 30 years. Currently, a large number of hanging galvanized steel pipes are used in national major projects such as steel, high-speed rail, and infrastructure. The galvanizing process is used for large parts in greenhouses, such as trusses and brackets.

2) Blow plating: It also requires acid washing and soaking in a zinc bath, but after lifting it up, it will go through a device to remove excess zinc before it is fully attached to the steel pipe. However, the amount of zinc added is slightly lower, with the current standard of around 200 grams, which is nearly twice the amount of zinc added compared to the hanging zinc process. This process has a low cost of steel pipes, a service life of 15-20 years, and high cost-effectiveness, As a commonly used galvanizing process.

3) Galvanized strip: pre coated with steel raw materials, then made into pipes, with low galvanizing amount and poor anti-corrosion ability. The amount of galvanizing is 50 grams per square meter, which will rust in 2-3 years. It is not recommended to use it in greenhouses.

4) Plastic coating: This process is a process that continues to increase corrosion resistance by coating the galvanized pipe with plastic after the completion of hot galvanizing. However, the average cost per ton of steel will increase by about 2000 yuan, which has not been used in greenhouse engineering due to its high cost.

Mainly identify the anti-corrosion of the surface

Hanging plating: Due to the thickness of the galvanized layer, the color is slightly darker than that of blowing plating and tape plating;

Galvanized strip: The zinc content is low, and the newly produced surface is bright, and after a period of time, it will show a bit of black. Secondly, professional equipment can use a zinc layer measuring instrument for professional measurements.

To South Africa: 45 days

To the Middle East: 30 days

To South America: 45 days

To North America: 30 days

To Russia: 7 days

To Europe: 45 days

To Korea: 5 days

To Japan: 5 days

To Vietnam: 15 days

To Thailand: 15 days

To India: 30 days

To Indonesia: 15 days

To Singapore: 15 days

Supplied products:Square steel pipe, circular steel pipe

Supply quantity: 70000 tons